Sex dolls are robust creations. They come from manufacturers who ensure that they can withstand even the not so careful handling by their owners.
However, as time passes by, sex dolls acquire damages. While some of these damages are irreparable, some can be restored if you have enough knowledge in repairing sex dolls.
If you are a TPE sex doll owner who wish to repair your damaged doll, the first tool that you need to have is a 1.5 kilowatts infrared gun. This tool is very useful as it shows you the real-time temperature feed of what you are repairing. One thing worth noting is that the repairs that you will do will depend on the degree of the sex doll’s damage. If the damage is minor, the process of repairing it will be short and simple.
One damage that your sex doll may acquire is some indentations due to the weight and impact that it gets. These indentations can be a cause of pressing the surface of your doll with heavy 0items.
Moreover, you can also cause the same damage to your doll if you lay her down improperly without correctly positioning her during sex. But, you do not need to worry about this damage because there are several procedures that you can follow to repair your beloved doll.
The Hot Towel Procedure
This simple repair process requires you to cover the visible dents on your doll with a hot, clean towel for a short span of time. Once the damaged part is already hot, put on a glove and pat the damaged area with your hand. Do these steps alternately until the indentation is no longer visible.
The Hair Dryer Method0
It appears that a hairdryer does not only work on a woman’s hair. While most of us think that this tool only works to dry a woman’s wet hair, it is also an excellent solution to repair your TPE sex doll.
What you will need for this method is a wet and clean towel. As much as possible, use a white cloth in order to avoid staining your sex doll. Cover the indentation marks with the wet towel and heat it with the hairdryer. Go on with this step for some time. Afterward, you will notice that the indentations will start to disappear little by little.
Repairing Sex Doll Abrasions
Aside from indentations, another common damage that your sex doll may get is abrasions and tears. That being said, there are a couple of ways that you can do in order to repair such kind of damage.
Use TPE Glue
Once you have located where the tear is, apply a small amount of TPE glue using a fine-tipped tool. Then, pull the two sides of the tear together and hold it for a couple of minutes until it becomes intact again.
But before applying the glue, make sure that the damaged area is completely clean. You can use 70% isopropyl alcohol to do this.
Using a spatula, apply the TPE repair coating solvent evenly on the inner part of the tear. Avoid having an excessive amount of TPE glue hanging on the spatula as it would cause too much glue to spread on the doll’s skin.
Once you have sealed the tear, use a clean cloth to wipe out the excess glue. Avoid using your fingers in removing the glue you squeezed out from the tear as it would cause unwanted prints on your doll.
Lastly, leave the doll as a safe place with no tension on the surface for 24 hours.
Fixing Abrasions On the Doll’s Skin Using the Heat Gun Procedure
The first thing that you need to do with this procedure is to clean the damaged surface of the doll using Vaseline o baby oil. Apart from these substances will clean your doll, they will also helo in distributing the heat more evenly.
After applying baby oil or Vaseline, start focusing the heat gun on the damaged area. Take note of the distance between the heat gun and the doll’s skin. Do not aim the gun too close to your sex doll or else it would end up with severe burns on its skin. The distance between the device and your doll must be at least four inches.
The melting temperature of the doll’s skin is somewhere around 110 degrees Celcius. Once the melting starts, you will see a glaze-like mirror finish. The time when you need to stop heating the skin of your doll depends on the fume that comes out from heating it.
Once you heat the required temperature, grab a piece of clean cloth to feather out the irregularities that the abrasion caused on your doll’s skin. Repeat the process of heating and cooling the doll’s skin several times. This is the secret to getting the fine finish as repeating the heating and cooling process will make the damaged part smooth.
One thing worth noting is that the temperature of the surface you heated will drop quite fast. So, it is important to smooth out the abrasion as soon as you stopped working with the heat gun.
Fixing the Facial Cuts of the Doll
You can fix facial cuts on your TPE sex doll using the similar processes mentioned above. However, it requires a lot of practice to do it perfectly. The right tools, as well as steady hands, are what you need in order to repair small facial cuts on your TPE doll.
But if it is your first time trying to fix a sex doll’s face, it would be more worth it if you would buy a new head for your sex doll instead. Apart from it will completely revamp your sex doll, it is also worth every dollar you spent.
The most robust and genuine branded doll heads cost around $400. You might think that this price is quite expensive. However, it is still an excellent bargain because you will have a stronger doll head than before.
Leave a Reply